WARNING WARNING OF PERFORMANCE GRINDING WHEELS OF EXTRACTIVE MATERIALS

Authors

DOI:

https://doi.org/10.20998/2078-7405.2020.92.17

Keywords:

relative wear, working surface of the wheels, intermittent grinding, cutting protrusion.

Abstract

When grinding circles, the working surface of which consists of periodically protrusions and depressions, in the elastic system of the machine due to the interruption of the cutting process there are high-frequency oscillations of small amplitude, which facilitate the process of chip formation and contribute to the formation of a developed cutting microrelief. However, at certain ratios of lengths of the cutting projections and depressions and at certain their quantities, parametric resonance may occur, which is a prerequisite for a periodic change in the stiffness time of the elastic system of the machine. Parametric resonance has a negative effect not only on the specific wear of the diamond kkol, but also on the quality of the machined surface. This implies the need for further exploration of the effect of parametric resonance arising from intermittent grinding on the relative flow of diamond circles. In the article, using the calculated and experimental ways, identified The extreme nature of the dependences of the specific wear of discontinuous circles of superhard materials on the number of slots on the working surface of the tool and on the ratio of the extent of the cavity to the length of the cutting ridge of the circle. Also, using the computational and experimental ways the characters of the influence of the dimensions and number of structural elements from which the working surface of diamond discontinuous circles was formed, as well as the rigidity of cutting on the parametric stability of the elastic system of a surface grinding machine, were revealed. The nature of the influence of the size and number of structural elements from which the working surface of diamond discontinuous wheels is formed, as well as the cutting rigidity on the parametric stability of the elastic system of the surface grinding machine is revealed by calculation and experiment.

Author Biographies

Oleksiy Yakimov, Odessa National Polytechnic University, Odessa

Doctor of science, professor, Head of the Department of Information Technology for Design in Mechanical Engineering Odessa National Polytechnic University, Odessa, Ukraine

Liubov Bovnegra, Odessa National Polytechnic University, Odessa

Associate Professor of the Department of Information Technology for Design in Mechanical Engineering, Odessa National Polytechnic University, Odessa, Ukraine

Sergey Uminsky, Odessa State Agrarian University, Odessa

Associate Professor of the Department of Agroengineering Odessa State Agrarian University, Odessa, Ukraine

Vladimir Tonkonogyi, Odessa National Polytechnic University, Odessa

Doctor of science, professor, Head of the Industrial Technologies, Design and Management Institute, Odessa National Polytechnic University, Odessa, Ukraine

Yuliia Smirnova, Odessa National Polytechnic University, Odessa

Student, Odessa National Polytechnic University, Odessa, Ukraine

References

Lukin, L.L. Raschet preryivistyih krugov pri ploskom periferiynom shlifovanii /L.L. Lukin, V.D. Starshev // Vestnik Izh.GTU. – 2007. – #1, – pp. 38-39.

Gunko, N.I. Issledovanie vliyaniya zhestkosti ploskoshlifovalnogo stanka na iznos abrazivnyih krugov pri preryivistom shlifovanii /N.I. Gunko // Chistovyie metodyi obrabotki: sb. nauchn. trudov. – Perm: Permskiy politehnicheskiy institut, 1971. – Vyip. 97, – pp. 3-8.

Gutsalenko, Yu.G. Stiykist kruga v robochih protsesah ratsionalnogo stabilnogo shlifuvannya // Visn. nats. tehn. un-tu «KharkIvskiy polItehnIchniy Institut» – 2005. – #23. – pp. 50-63.

Almaznaya obrabotka: uchebn. posobie [dlya stud. vyissh. uch. zaved.] /A.V. Yakimov, F.V. Novikov, G.V. Novikov, A.A. Yakimov. – K.: ISMO, 1996. – 168 p.

Tehnologiya mashinostroeniya: Uchebnik. /A.V. Yakimov, F.V. Novikov, P.A. Linchevskiy,V.P. Larshin,E.V. Grisenko, A.A. Yakimov, A.V. Fadeev, G.V. Novikov. - Odessa: ONPU, 2012.- 693 p.

Yakimov, A.V. Vyisokoproizvoditelnaya obrabotka abrazivno-almaznyimi instrumentami: uchebn. posobie [dlya stud. vyissh. uchebn. zaved.] / A.V. Yakimov, F.V. Novikov, A.A. Yakimov. – Kyiv: Tehnika, 1993, – 152 p.

Radzevich, S.P. Dudleys Handbook of Practical Gear Design and Manufacture/ 2-nd Edition, SRS Press, Boca Raton, Flonda, 2011, 1111 pages.

Semko, M.F. Osnovyi almaznogo shlifovaniya/M.F. Semko, A.I. Grabchenko, A.F. Rab, M.D. Uzunyan, M.S. Pivovarov. – Kyiv: Tehnika, 1978, – 192 p.

Downloads

Published

2020-07-01

Issue

Section

Mechanical processing of materials, the theory of cutting materials, mathematical and computer simulation of machining p