INFLUENCE OF MEASUREMENT SETTINGS ON AREAL ROUGHNESS WITH CONFOCAL CHROMATIC SENSOR ON FACE-MILLED SURFACE

Authors

  • Nagy Antal University of Miskolc, Hungary

DOI:

https://doi.org/10.20998/2078-7405.2020.93.08

Keywords:

surface roughness, areal roughness, confocal chromatic sensor.

Abstract

Roughness measurement is of highlighted importance in production for describing the quality control of manufacturing processes for the functional, tribological, etc. properties of the surfaces of parts. In the last 15 years or so the areal roughness studied on topographies has also become more common, as it provides a more accurate and detailed characterization of the surfaces. However, with relatively little experience and different technical conditions, topographies are analyzed differently. Sometimes 3D topography is used only as an illustration; however, spatial roughness measurement can provide much more information. The effect of measurement speed and point density during roughness measurement on the areal roughness was investigated using a confocal chromatic sensor.

Author Biography

Nagy Antal, University of Miskolc

Engineering teacher, Department of Production Engineering, University of Miskolc, Miskolc - Egyetemváros, Hungary

References

I. Zagórski, J. Korpysa: Surface Quality Assessment after Milling AZ91D Magnesium Alloy Using PCD Tool, Materials vol.13(3) (2020) ArtNo:617.

B. Karpuschewski, J. Kundrák,

T. Emmer, D. Borysenko: A New Strategy in Face Milling - Inverse Cutting Technology, Solid State Phenomena vol.261 (2017) pp.331-338.

J. Kundrak, C. Felho: 3D roughness parameters of surfaces face milled by special tools, Manufacturing technology vol.16(3) (2016) pp.532-538.

G. Varga, J. Kundrák: Effects of Technological Parameters on Surface Characteristics in Face Milling, Solid State Phenomena vol.261 (2017) pp.285-292.

Jiang, X., Scott, P. J., Whitehouse, D. J., Blunt, L.: Paradigm shifts in surface metrology. Part I. Historical philosophy, Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences vol.463(2085), (2007) pp.2049-2070.

S.K. Fecske, K. Gkagkas, C. Gachot, A. Vernes: Interdependence of Amplitude Roughness Parameters on Rough Gaussian Surfaces, Tribology Letters vol.68(1) (2020) pp.1-15.

K. Klauer, M. Eifler, B. Kirsch, J. Seewig, J.C. Aurich: Ball end micro milling of areal material measures: influence of the tilt angle on the resulting surface topography, Production Engineering vol.14(2) (2020) pp.239-252.

M. Niemczewska-Wójcik, A. Wójcik: The multi-scale analysis of ceramic surface topography created in abrasive machining process, Measurement vol.166 (2020) ArtNo:108217.

S. Wojciechowski, R. Talar, P. Zawadzki, S. Legutko, R. Maruda, C. Prakash: Study on Technological Effects of a Precise Grooving of AlSi13MgCuNi Alloy with a Novel WCCo/PCD (DDCC) Inserts, Materials vol.13(11) (2020) ArtNo:2467.

K Mouralova, L Benes, T Prokes, J Bednar, R. Zahradnicek, J. Fries: Machining of pure molybdenum using WEDM, Measurement vol.163 (2020) ArtNo:108010.

Geometrical product specifications (GPS) — Surface texture: Areal — Part 3: Specification operators. ISO 25178-3:2012. Geneva: International Organization for Standardization.

Published

2020-12-31

Issue

Section

Mechanical processing of materials, the theory of cutting materials, mathematical and computer simulation of machining p