DEVELOPMENT OF TECHNOLOGY AND COMPARATIVE ANALYSIS OF CREATING THREE-DIMENSIONAL MODELS IN MODERN CAD SYSTEMS TAKING INTO ACCOUNT THE FORMATION PROCESSES BY CUTTING

Authors

  • Volodymyr Tigarev Odessa National Polytechnic University, Odessa, Ukraine
  • Volodymyr Tonkonogyi Odessa National Polytechnic University, Odessa, Ukraine
  • Vladyslav Vaysman Odessa National Polytechnic University, Odessa, Ukraine
  • Julia Babych Odessa National Polytechnic University, Odessa, Ukraine
  • Vira Salii Odessa National Polytechnic University, Odessa, Ukraine

DOI:

https://doi.org/10.20998/2078-7405.2019.90.10

Keywords:

computer model, algorithm, the parametric design, synchronous design.

Abstract

A sequence over of development of computer is brought technologies on creation of model of detail with the use of various approaches. The self-reactance planning, direct design is considered, (without the tree of construction and hard connections between structural elements), variation design. Similar decisions were used exceptionally for to the 2d-sketch and constructions of connections "from top to bottom" for frame-clamping knots that did not embrace a three-dimensional design. A situation changed with appearance of synchronous technology, that was able to spread the variation going near a design on all chainlet of planning of good. It is synchronous technology allows to change the functional of direct design directly in a self-reactance environment. The algorithm of creation of three-dimensional model of detail is worked out in a synchronous environment. In an algorithm thoroughly to consider all stages of creation of three-dimensional model of detail from a requirement specification to the model and designer documentation. The technology of creating a three-dimensional model details the type of housing in the synchronous design environment of modern CAD Solid Edge. The features of creating and editing a three-dimensional model of the part and its elements are given in detail, taking into account the features of technological processes of forming cutting. It is considered as by means of managing 3d-розмірів and geometrical connections between 3d-об'єктами exact control of geometry is realized in synchronous technology. In Solid Edge with synchronous technology structural elements are independent and kept not in the tree of model, but in a navigator. Computer imitation models allow operatively to investigate and pick up the optimal modes and parameters of technological process, that promotes efficiency, exactness and quality of production considerably. Modern technologies not only simplify work to the engineer-designer, but also considerably cut prime cost production. A comparative analysis of the design in synchronous and parametric environments with an explanation of the advantages and disadvantages. Synchronous technology unites in itself advantages of self-reactance and direct design, and eliminates the lacks of both approaches.

Author Biographies

Volodymyr Tigarev, Odessa National Polytechnic University, Odessa

Associate professor, Odessa National Polytechnic University, Odessa

Volodymyr Tonkonogyi, Odessa National Polytechnic University, Odessa

Director of the Institute of Industrial Technologies, Design and Management, Professor of the Department, Odessa National Polytechnic University, Odessa

Vladyslav Vaysman, Odessa National Polytechnic University, Odessa

Professor, Odessa National Polytechnic University, Odessa

Julia Babych, Odessa National Polytechnic University, Odessa

Associate professor, Odessa National Polytechnic University, Odessa

Vira Salii, Odessa National Polytechnic University, Odessa

Assistant, Odessa National Polytechnic University, Odessa

References

Fetisov G.P. Materialovedenie i tehnologiya materialov. — M.:Yurayt, 2014.—767s.

.Shahnov V.A., Zinchenko L.A. I In. Osnovyi konstruirovaniya v Solid Edge. Posobie po proektirovaniyu izdeliy v priborostroenii. – M.: DMK Press, 2014. – 272 s.

Demidov P. Sinhronnaya tehnologiya Solid Edge [Electronic resource]//Proekt isicad. 28.07.2015.–URL: http://isicad.ru/ru/articles.php?Article _num=17898.

TigarEv V.M., SalIy V.I., Zaytsev P. Rozrobka tehnologIYi stvorennya trivimIrnoYi modelI v sinhronnomu seredovischI proektuvannya suchasnih SAPR// II MIzhnarodna konferentsIya «Virobnitstvo & MehatronnI Sistemi 2018» . – HarkIv : HNURE, 2018. – 77-81 s.

Fast and easy creation of 3D models using synchronous technology Solid Edge Edge [Electronic resource]// Material Library Siemens PLM Software–URL: https://solidedge.siemens.com/ru/solutions/products /3d_design /synchronous_technology/#ui_Fast_and _Flexible_Design_Creation.

Zinovev D.V. Osnovyi konstruirovaniya v Solid Edge ST10/. 2018. – 206 s.

Ryan McVay. Solid Edge with Synchronous Technology—Many Things at the Same Time [Electronic resource] Proekt engineering. 27.05.2016.–URL:https://www.engineering.com /DesignSoftware/DesignSoftwareArticles/ArticleID/12223/Solid-Edge-with-Synchronous-Technology Many -Things-at-the-Same-Time.aspx

MLombard Retired. Synchronous AND Parametric [Electronic resource] Proekt Siemens PLM Community. 15.04.2015.–URL:https://community.plm.automation. siemens.com/t5/Solid-Edge-Blog/Synchronous-AND-Parametric/ba-p/297109

Ryan McVay. Synchronous Technology—Debunking the Myths [Electronic resource] Proekt engineering. 26.06.2017.–URL: https://www.engineering.com/Design Software/DesignSoftwareArticles/ArticleID/ 15056/Synchronous-TechnologyDebunking-the-Myths.aspx?e_src=relart

S.I.Pestretsov. Kompyuternoe modelirovanie i optimizatsiya protsessov rezaniya. – Tambov:TGTU, 2009. – 94 s.

Published

2019-05-01

Most read articles by the same author(s)