MECHANO-PHYSICO-CHEMICAL MODELING OF THE PROCESS OF DESTRUCTION OF THE PART SURFACE IN A FREE ABRASIVE MEDIUM

Authors

DOI:

https://doi.org/10.20998/2078-7405.2020.92.08

Keywords:

abrasive granules, the processed surface, cutting, plastic deformation, friction, traces of processing, destruction of the material.

Abstract

The analysis of the phenomena in the zone of collision of the working medium granules with the parts surface is presented. It is noted that the abrasive granules of are embedded in the processed part surface by the grains protruding from the bundle. It is indicated that the contact of the abrasive granule with the part surface carried out within small size areas, determined by the strength of the collision, the number and state of the active grains, their level of fixation, dimensions and physical and mechanical properties of the part material. The behavior of a single granule moving relative to the processed part is considered. The main types of abrasive grain action on the processed surface are highlighted, that is, cutting, plastic deformation and friction, it is noted that over time, abrasive grain can initially perform only friction, then plastic deformation, then cutting. It is established that such an alternation of the abrasive grains work is associated with the nature of the movement of the granules on the surface of the processed part. High-speed video recording of single processing traces showed that granules leave on contact surfaces the processing traces that are difficult to outline, differ in depth and location on the surface. It was determined that the track depth changes in the direction of granule movement and is calculated by the speed of its movement, as well as by the strength and frequency of penetration into the material of the part during contact. Electron microscopic studies show the presence of adhesive spots and oxide films at the contact sites. This confirms that in the process under consideration, as well as during grinding, polishing, and finishing, continuous exposure of juvenile surfaces occurs. It was established that the interaction of active juvenile surfaces and plastically deformed volumes of metal with aggressive components of the working medium leads to the formation of secondary weakened structures on their surface, the layer thickness of which is 0.05 ... 0.08 μm. The parameters of the processing mode that determine the nature of the physical and mechanical processes of interaction of the single granule and the processed part are established. The differences of the vibrating abrasive treatment method from the known finishing methods are considered. The mechanism of destruction of the part material is shown and the stages of mechanical and physicochemical modeling of the process of vibrating abrasive treatment are presented.

Author Biographies

Mitsyk Andrii , Volodymyr Dahl East Ukrainian National University, Severodonetsk, Luhansk oblast

Candidate of Technical Sciences, Associate Professor, Department of mechanical engineering and applied mechanics, Volodymyr Dahl East Ukrainian National University, Severodonetsk, Luhansk oblast, Ukraine

Fedorovich Vladimir, National Technical University "Kharkiv Polytechnic Institute", Kharkiv

Doctor of Technical Sciences, Professor, Department "Integrated Technologies of Mechanical Engineering named after MF Semko", National Technical University "Kharkiv Polytechnic Institute", Kharkiv, Ukraine

Grabchenko Anatoliy, National Technical University "Kharkiv Polytechnic Institute", Kharkiv

Doctor of Technical Sciences, Professor, Department "Integrated Technologies of Mechanical Engineering named after MF Semko", National Technical University "Kharkiv Polytechnic Institute", Kharkiv, Ukraine

References

Babichev A.P. Osnovyi vibratsionnoy tehnologii / A.P. Babichev, I.A. Babichev. – Rostov n/D: Izdatelskiy tsentr DGTU, 2008. – 694 p.

Kartashov I.N. Obrabotka detaley svobodnyimi abrazivami v vibriruyuschih rezervuarah / I.N. Kartashov, M.E. Shainskiy, V.A. Vlasov. – Kyiv: Vischa shkola, 1975. – 188 p.

Politov I.V. Vibratsionnaya obrabotka detaley mashin i priborov / I.V. Politov, M.A. Kuznetsov. – L.: Mashinostroenie, 1965.

Rebinder P.A. Vliyanie aktivnyih smazochno-ohlazhdayuschih zhidkostey na kachestvo poverhnosti pri obrabotke metallov rezaniem i davleniem. – Moscow: Izd-vo AN SSSR, 1946. – 432 p.

Babichev A.P. Primenenie vibratsionnyih tehnologiy na operatsiyah otdelochno-zachistnoy obrabotki detaley (ochistka, moyka, udalenie obloya i zausentsev, obrabotka kromok) / A.P. Babichev, P.D. Motrenko, L.K. Gillespi. Rostou-na-Donu: DGTU. – 2010. – 289 p.

Kostetskiy B.I. Trenie, smazka i iznos v mashinah / B.I. Kostetskiy. – Kyiv, 1970.

Babichev A.P. Vibratsionnyie stanki dlya obrabotki detaley / A.P. Babichev, V.B. Trunin, Yu.M. Samodumskiy, V.P. Ustinov. – Moscow: Mashinostroenie, 1984. – 168 p.

Published

2020-07-01

Issue

Section

Mechanical processing of materials, the theory of cutting materials, mathematical and computer simulation of machining p