EXPERIMENTAL INVESTIGATION OF TRIBOLOGY-RELATED SURFACE TOPOGRAPHY PARAMETERS AND HARDNESS OF 16MNCR5 CASE HARDENED STEEL

Authors

DOI:

https://doi.org/10.20998/2078-7405.2023.98.07

Keywords:

HV hardness, surface roughness, Ssk; Sbi, hard machining

Abstract

Tribological properties are determinant in the functionality of contacting surfaces of machine elements. The wear resistance or load bearing capacity influence the lifetime of these parts. In this study tribology-related surface topography parameters (Ssk, Sbi) and the hardness of hard turned surfaces are analyzed after hardness and topography measurements. Correlation coefficients were calculated for their relationships. It was found that the cutting parameters affect the wear resistance and the hardness in the opposite direction.

Author Biography

Nagy Nora, University of Miskolc, Hungary

Assistant lecturer, Faculty of Mechanical Engineering and Informatics, Institute of Material Science and Technology, University of Miskolc, Hungary

References

Fedorovich,V., Pyzhov, I., Ostroverkh, Y., Pupan, L., Garachenko, Y.: Methodology for developing an expert system for the grinding of superhard materials, Rezanie i Instrumenty v Tekhnologicheskih Sistemah 96, pp. 82–88, 2022.

Lavrinenko, V., Solod, V.: The ralationship betwheen the parameters of roughness and features of surface formation with a special microprofile, Rezanie i Instrumenty v Tekhnologicheskih Sistemah 96, pp. 99–109, 2022.

Kovalchuk, O., Nezhebovsky, V., Permyakov, O., Klochko, O., Ryabchenko, S.: Processing of hardened cylindrical gear wheels of the cutting gearbox of the combine UKD 200-500, Rezanie i Instrumenty v Tekhnologicheskih Sistemah 95, pp. 57–70, 2021.

Yakimov, O., Uminsky, S., Klimenko, N., Kirkopulo, K., Pavlyshko, A., Vaysman, V.: Improving grinding of gear wheels applied in gearboxes of power engineering, Rezanie i Instrumenty v Tekhnologicheskih Sistemah 95, pp. 45–56, 2021.

Kundrak, J., Sztankovics, I., Molnar, V.: Accuracy and topography analysis of hard machined surfaces, Manufacturing Technology 21(4), pp. 512–519, 2021.

Zawada-Tomkiewicz, A.: Analysis of surface roughness parameters achieved by hard turning with the use of PCBN tools, Estonian Journal of Engineering 17, paper 88, 2011.

Kundrak, J., Deszpoth I., Molnar V.: Decision support method for the applicability of hard turning, Rezanie i Instrumenty v Tekhnologicheskih Sistemah 96, pp. 110–120. 2022.

Heinzel, J., Jedamski, R., Rößler, M., Karpuschewski, B., Epp, J., Dix, M.: Hybrid approach to evaluate surface integrity based on grinding power and Barkhausen noise, Procedia CIRP 108, pp. 489–494, 2022.

Kundrak J., Deszpoth, I., Molnar, V.: Comparative study of material removal in hard machining of bore holes, Tehnicki Vjesnik-Technical Gazette 21(1), pp 183–189, 2014.

Gapinski, B., Firlik, B., Mathia, T.G.: Characteristics of tram wheel wear: Focus on mechanism identification and surface topography, Tribology International 150, paper 106365, 2020.

Alok, A., Das, M.: White layer analysis of hard turned AISI 52100 steel with the fresh tip of newly developed HSN2 coated insert, Journal of Manufacturing Processes 46, pp. 16–25, 2019.

Molnar V.: Asymmetric height distribution of surfaces machined by hard turning and grinding, Symmetry 14(8), paper 1591, 2022.

Sedlacek, M., Podgornik, B., Vizintin, J.: Correlation between standard roughness parameters skewness and kurtosis and tribological behaviour of contact surfaces, Tribology International 48, pp. 102–112, 2012.

Sedlacek, M., Gregorcic, P., Podgornik, B.: Use of the roughness parameters Ssk and Sku to control friction – a method for designing surface texturing, Tribology Transactions 60, pp. 260–266, 2017.

Molnar, V., Sztankovics, I.: Analysis of roughness parameters determining tribological properties in hard turned surfaces, Hungarian Journal of Industry and Chemistry 49(2), pp. 77–84, 2021.

Yu, N., Polycarpou, A.A.: Combining and contacting of two rough surfaces with asymmetric distribution of asperity heights, Journal of Tribology 126, pp. 225–232, 2004.

Pawlus, P., Reizer, R., Zelasko, W.: Prediction of parameters of equivalent sum rough surfaces, Materials 13, paper 4898, 2020.

Orrillo, P.A., Santalla, S.N., Cuerno, R., Vazquez, L., Ribotta, S.B., Gassa, L.M., Mompean, F.J., Salvarezza, R.C., Vela, M.E.: Morphological stabilization and KPZ scaling by electrochemically induced co-deposition of nanostructured NiW alloy films, Scientific Reports 7, paper 17997, 2017.

Gadelmawla, E.S., Koura, M.M., Maksoud, T.M.A., Elewa, I.M., Soliman, H.H.: Roughness parameters, Journal of Material Processing Technology 123, pp. 133–145, 2002.

Grzesik, W.: Prediction of the functional performance of machined components based on surface topography: state of the art, Journal of Materials Engineering and Performance 25(10), pp. 4460–4468, 2016.

Molnar V.: Analysis of the Sbi and Svi functional indices in hard machining, Rezanie i Instrumenty v Tekhnologicheskih Sistemah 97, pp. 113–123, 2022.

Grzesik, W., Zak, K., Kiszka, P.: Comparison of surface textures generated in hard turning and grinding operations, Procedia CIRP 13, pp. 84–89, 2014.

Korzynski, M., Dudek, K., Palczak, A., Kruczek, B., Kocurek, P.: Experimental models and correlations between surface parameters after slide diamond burnishing, Measurement Science Review 18, pp. 123–129, 2018.

Deltombe, R., Kubiak, K.J., Bigerelle, M.: How to select the most relevant 3D roughness parameters of a surface?, Scanning 36, pp. 150–160, 2014.

Molnar, V.: Tribological properties and 3D topographic parameters of hard turned and ground surfaces, Materials 15(7), paper 2505, 2022.

Struzikiewicz, G., Sioma, A.: Evaluation of Surface Roughness and Defect Formation after The Machining of Sintered Aluminum Alloy AlSi10Mg, Materials 13, paper 1662, 2020.

Elbah, M., Laouici, H., Benlahmidi, S., Nouioua, M., Yallese, M.: Comparative assessment of machining environments (dry, wet and MQL) in hard turning of AISI 4140 steel with CC6050 tools, International Journal of Advanced Manufacturing Technology 105, pp. 2581–2597, 2019.

Vishwanatha, J.S., Srinivasa Pai, P.: Application of Edge Detection Technique for Surface Roughness Estimation of Ti-6Al-4V Turned Surfaces, Manufacturing Technology 21, pp. 269–277, 2021.

Li, S., Chen, T., Qiu, C., Wang, D., Liu, X.: Experimental investigation of high-speed hard turning by PCBN tooling with strengthened edge, International Journal of Advanced Manufacturing Technology 92, pp. 3785–3793, 2017.

Molnar, V.: Tribology and Topography of Hard Machined Surfaces, Rezanie i Instrumenty v Tekhnologicheskih Sistemah 94, pp. 49–59, 2021.

Downloads

Published

2023-05-25

Issue

No. 98 (2023): Cutting and Tools in Technological Systems

Section

Mechanical processing of materials, the theory of cutting materials, mathematical and computer simulation of machining p

License

Copyright Notice

Authors who publish with this Collection agree to the following terms:

1. Authors retain copyright and grant the Collection right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this Collection.

2. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the Collection's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this Collection.

3. Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work.